72v 20ah 3000w LuxuryEbikes Kit

This high-powered 3000W 72v e-Bike rear hub motor kit is a major upgrade from 1000W and 1500W options. It delivers significantly more torque and a higher top speed, while still being compatible with most bikes featuring a 135mm dropout width. It’s important to review your local laws and regulations to ensure this kit is suitable before making a purchase. Wink Wink.

PACKAGE CONTENTS

• 1 x 3000W brushless direct-drive (gearless) rear hub motor, laced to a strong MTX rim with XT150 connectors
• 1x 72v 20ah 60amp Battery
• 1x 3amp 84v Charger
• 10x Battery Straps
• 1 x 60A brushless motor controller 
• 1 x LCD SW900 display (or UKC1 display or plus version)
• 1 x pedal assist crank sensor (PAS)
• 1 x right-hand throttle (full twist) with a matching left-hand handlebar grip
• 1 x pair of brake levers (compatible with mechanical/cable brakes)

DESCRIPTION

This kit provides far more power than our 1000W or 1500W kits, reaching speeds of over 85km/h. Please comply with your local laws by setting the speed limiter to 25km/h and 250W when riding in public areas. Only generic instructions are included due to the many DIY possibilities, but assistance is available if needed DM on Instagram.

KEY FEATURES

• Wheel Type: Rear Wheel
• Battery Connecter: XT60
  
• Range: 55km
• Battery Charge Plug: AUS,USA,UK,CANADA
• Dropout: 135mm (fits most bikes, not compatible with thru axles)
• Wheel Size: 26", 27.5", or 29"
• Rim: Alloy double-wall with a 33mm internal width
• Gears: Freewheel / screw-on (not compatible with cassette)
• Motor: Brushless DC direct drive
• Torque: 85 Nm
• Power: 3000W
• Max Speed: 90+ km/h
• Spokes: Steel 12Gx2.6mm
• Weight: 6 kg
• Wheel Axle: 210mm x 10mm
• Max Load Capacity: 150 kg (including bike and rider)

WARRANTY

• General wear and tear is not covered.
• Damages caused by improper installation are not covered. Please contact us if unsure about fitting or operating the kit.
• Ensure proper alignment and protection of the wiring from the motor axle to avoid damage, which is not covered under warranty.
• Ensure the motor axle is fully seated in the bike’s dropouts and the 21mm axle nuts are tightened securely. Damage from improper installation is not covered.
• When operating in full power mode, fitting a torque arm (sold separately) on both sides is highly recommended to prevent the axle from spinning within the dropouts, which could damage the wiring. This damage is not covered by warranty.
• To properly fit the kit, you may need a 5mm steel spacer behind the disc rotor and longer disc rotor bolts. The plastic spacer included is for transport only.
• The kit is not waterproof and should not be submerged in water.
• A 6 month warranty is provided from the date of receipt.
• While this kit is known for durability, misuse, including jumps, impacts with curbs, exceeding the weight limit, or downhill riding, is not covered by warranty. The kit is best suited for smooth surfaces and light gravel paths.

NOTES

• Press the 'M' button on the LCD display to power on and unlock the full potential of the kit.
• The rim is best suited for 2.35” to 2.5” wide tires.
• Australian regulations require that the kit be limited to 250W and 25km/h on public roads. To comply, adjust the 'P08' setting to 25km/h in the LCD display. Hold the ‘UP’ and ‘DOWN’ buttons for 1 second after powering on the kit, then short-press ‘M’ to navigate through the ‘P’ settings until reaching 'P08.'

NOT INCLUDED

Torque arms, installation tools, freewheel gear, specific instructions, and disc brakes.